- Manual bp cuff with gauge
- Free E-newsletter
- Best Manual Blood Pressure Cuffs
- Appointments at Mayo Clinic
- Shop by category
- Get a Free Tips for Accurate Blood Pressure Poster
- Instructions for How to Calibrate a Sphygmomanometer
- 10 Steps to Accurate Manual Blood Pressure Measurement
- How Blood Pressure Readings Work
If you purchase a manual or digital blood pressure monitor sphygmomanometer , follow the instruction booklet carefully. The following steps provide an overview of how to take your left arm blood pressure on either a manual or digital blood pressure monitor. Simply reverse the sides to take a blood pressure in your right arm. Locate your pulse by lightly pressing your index and middle fingers slightly to the inside center of the bend of your elbow where the brachial artery is.
If you cannot locate your pulse, place the head of the stethoscope on a manual monitor or the arm cuff on a digital monitor in the same general area.
Slide the cuff onto your arm, making sure that the stethoscope head is over the artery when using a manual monitor. The cuff may be marked with an arrow to show the location of the stethoscope head.
Manual bp cuff with gauge
The lower edge of the cuff should be about 1 inch above the bend of your elbow. Use the fabric fastener to make the cuff snug, but not too tight.
If you released the pressure too quickly or could not hear your pulse, DO NOT inflate the cuff again right away. Wait one minute before repeating the measurement. Start by reapplying the cuff. Follow your doctor's instructions on when and how often you should measure your blood pressure. Record the date, time, systolic and diastolic pressures.
You should also record any special circumstances like any recent exercise, meal, or stressful event. This is done by comparing a blood pressure reading from your machine with one from the doctor's office machine. Reviewed by William Blahd on May 10, It is intended for general informational purposes only and does not address individual circumstances.
It is not a substitute for professional medical advice, diagnosis or treatment and should not be relied on to make decisions about your health. Never ignore professional medical advice in seeking treatment because of something you have read on the WebMD Site. If you think you may have a medical emergency, immediately call your doctor or dial This tool does not provide medical advice.
See additional information. How do I do a step-by-step blood pressure check? ANSWER If you purchase a manual or digital blood pressure monitor sphygmomanometer , follow the instruction booklet carefully. Locate your pulse Locate your pulse by lightly pressing your index and middle fingers slightly to the inside center of the bend of your elbow where the brachial artery is.
Secure the cuff Slide the cuff onto your arm, making sure that the stethoscope head is over the artery when using a manual monitor.
Best Manual Blood Pressure Cuffs
Place the stethoscope in your ears. Tilt the ear pieces slightly forward to get the best sound.
Inflate and deflate the cuff If you are using a manual monitor: You'll get the most accurate reading if your arm is held straight. Record your blood pressure. Hold the pressure gauge in your left hand and the bulb in your right. Close the airflow valve on the bulb by turning the screw clockwise.
Appointments at Mayo Clinic
Inflate the cuff by squeezing the bulb with your right hand. You may hear your pulse in the stethoscope. Watch the gauge. Keep inflating the cuff until the gauge reads about 30 points mm Hg above your expected systolic pressure. At this point, you should not hear your pulse in the stethoscope.
Keeping your eyes on the gauge, slowly release the pressure in the cuff by opening the airflow valve counterclockwise. The gauge should fall only 2 to 3 points with each heartbeat. You may need to practice turning the valve slowly. Listen carefully for the first pulse beat. As soon as you hear it, note the reading on the gauge.
This reading is your systolic pressure the force of the blood against the artery walls as your heart beats. Continue to slowly deflate the cuff. Listen carefully until the sound disappears.
Shop by category
As soon as you can no longer hear your pulse, note the reading on the gauge. This reading is your diastolic pressure the blood pressure between heartbeats. Allow the cuff to completely deflate. Hold the bulb in your right hand. Press the power button.
Get a Free Tips for Accurate Blood Pressure Poster
All display symbols should appear briefly, followed by a zero. This indicates that the monitor is ready. If you have a monitor with automatic cuff inflation, press the start button.
Sit quietly and watch the monitor. Pressure readings will be displayed on the screen. For some devices, values may appear on the left, then on the right.
Wait for a long beep. This means that the measurement is complete. Note the pressures on the display screen.
Instructions for How to Calibrate a Sphygmomanometer
Systolic pressure the force of the blood against the artery walls as your heart beats appears on the left and diastolic pressure the blood pressure between heartbeats on the right.
Your pulse rate may also be displayed in between or after this reading. Allow the cuff to deflate. What should I do before checking my blood pressure? More Answers On Hypertension How is the blood pressure measure written and what does it mean?
10 Steps to Accurate Manual Blood Pressure Measurement
How is hypertension diagnosed? If you're diagnosed with high blood pressure, what tests might your doctor recommend?
How Blood Pressure Readings Work
What is systolic and diastolic blood pressure? Other Answers On:. Cholesterol Management Heart Disease. Is My Penis Normal?